Instructions for Constructing a Raccoon Trap

Posted by

Home Improvement

Raccoon traps are tools or devices used to capture raccoons. Utah-based Photographer Ryan Hou / Getty Images

Raccoons are adorable, but they can be quite bothersome if they decide to move into your yard, chimney, or attic. Luckily, you can make a highly effective homemade raccoon trap at a minimal or no cost [source: Trapping Raccoons]. We will illustrate how to make two types of raccoon traps.

Picnic Table Trap

You will require the following items:

  • A tall and sturdy trash can
  • A picnic table or another lengthy object that is at least as high as the trash can.
  • A plank of wood
  • Bait (such as meat or fish scraps or even marshmallows!)

Here’s how to prepare the trap:

  1. Place the trash can near the table’s end and secure it with rocks or bricks so that it doesn’t tip over.
  2. Fill the trash can with water, about a quarter to a third of the way full.
  3. Take the plank and place it on the table with one end hanging over part of the trash can. The board should remain on the table but should be able to tilt and fall when the raccoon steps out onto the overhang.
  4. Put the bait on the overhang. Do this near nightfall so that birds or other animals do not take the bait [source: Picnic Table Raccoon Trap].
  5. Check the trap the following morning. If the raccoon is caught, take it to a distant location and release it carefully. Remember, the raccoon may be hostile.

Cinder Block Trap

You will require the following items:

  • A tall and sturdy trash can
  • Two cinder blocks
  • Bait

Here’s how to make the trap:

  1. Place the trash can in an accessible location.
  2. Stand one cinder block upright against the trash can.
  3. Lay the second cinder block on its side at the bottom of the trash can.
  4. Place the bait on the second cinder block [source: Cinder Block Raccoon Trap].
  5. Check the trap the next morning. If the raccoon is caught, take it to a distant location and release it with utmost care.


1. What materials do I need to build a raccoon trap?

To build a raccoon trap, you will need a sturdy wire mesh, pliers, a metal cutter, a wooden plank, screws, nails, and a bait. The wire mesh should be at least 3 feet long and 2 feet wide. The wooden plank should be at least 4 feet long and 6 inches wide.

2. How do I construct the trap?

First, cut the wire mesh into three pieces – two pieces for the sides and one piece for the top. Then, attach the sides to the wooden plank using screws or nails. Next, attach the top piece to the sides using pliers and metal cutters. Ensure that there is a small opening for the raccoon to enter the trap. Lastly, place the bait at the end of the trap, and you are ready to catch a raccoon.

3. What type of bait should I use?

For a raccoon trap, you can use anything that is sweet and fragrant. Some popular options include peanut butter, marshmallows, sweet corn, and honey. Ensure that the bait is fresh and replaced regularly to attract the raccoon.

4. Where should I place the trap?

The trap should be placed in an area where raccoons are likely to be found. Consider placing it near a garbage can or in a wooded area. Ensure that the trap is placed on level ground and secured to prevent it from tipping over.

5. What precautions should I take when handling a trapped raccoon?

When handling a trapped raccoon, it is essential to wear gloves and protective clothing to avoid bites or scratches. Avoid approaching the raccoon from the front, as they can be aggressive. Instead, approach from the back and use a long stick or pole to move the trap. It is also advisable to release the raccoon far away from your property to prevent it from returning.

6. Is it legal to trap raccoons?

The legality of trapping raccoons varies depending on your location. It is essential to check your local laws and regulations before setting up a trap. In some areas, it is legal to trap raccoons, while in other areas, it may require a license or permit.

Leave a Reply

Your email address will not be published. Required fields are marked *